its been awhile, but my project car isnt dead just yet. I have taken some time off from it, frustrated after getting screwed over by aidan, and being distracted by my new ITB racecar, but im done with it until next spring, so now im back to the project car.
anyway, I have finally figured out how to get the quarter skins on there properly, still putting together the body, engine is half built, decided on a ls/vtec 1800, pr3 pistons, itr cams, s1 lsd tranny, for cost reasons, im staying n/a and using the zdyne ecu and harness that i already have, I havent found the cams yet, but im sure some will turn up before long.
since I wont be getting a CF mugen wing (explaination here: scammer thread , I have been working on a hatch with extended mugen style wing, unitized together, and having it reproduced in CF or FG. More on that later.
It does feel good to be working on it again, should be done by the end of the year.
3
Finally, My Own Build Thread
Started by evilGearhead, Oct 11 2005 01:18 AM
126 replies to this topic
#31
Posted 23 July 2006 - 01:21 AM
#32
Posted 23 July 2006 - 01:38 AM
Nice to see you back at it, I am excited to look forward to what you produce for us in the near future hopefully
-Zak
-Zak
He who dies with the most toys, wins.
#33
Posted 24 July 2006 - 12:16 AM
finally , i have a complete quarter panel! you guys who have installed these before will probably agree with me that its an accomplishment, indeed!
the other side should go together much quicker, now that Ive figured it out.
the other side should go together much quicker, now that Ive figured it out.
#34
Posted 24 July 2006 - 12:59 AM
nice build its looking pretty cool so far. keep up the good work chap *thumb up*
#35
Posted 08 August 2006 - 03:52 AM
both quarters are blended in, and basically done, i have shaped and instaled one front fender,
pistons are cleaned up and check out ok, all I need for the bottom end is a set of aftermarket rods, bearings, and rings..
dug my extra hatch out of the parts pile, going to pull the glass this weekend, clean it up, and get started on the one piece hatch/wing
any ideas as what material to use for this? I plan to make the wing out of ? material, glue or screw it on the hatch, glaze it with bondo, then have the molds made..
is there a type of sandable foam or other easy to deal with substance for this purpose?
pistons are cleaned up and check out ok, all I need for the bottom end is a set of aftermarket rods, bearings, and rings..
dug my extra hatch out of the parts pile, going to pull the glass this weekend, clean it up, and get started on the one piece hatch/wing
any ideas as what material to use for this? I plan to make the wing out of ? material, glue or screw it on the hatch, glaze it with bondo, then have the molds made..
is there a type of sandable foam or other easy to deal with substance for this purpose?
#36
Posted 08 August 2006 - 06:51 AM
QUOTE (evilGearhead @ Aug 8 2006, 03:52 AM)
any ideas as what material to use for this? I plan to make the wing out of ? material, glue or screw it on the hatch, glaze it with bondo, then have the molds made..
I like the idea of the doublesided tape, to attach it. But at the same time I am running into fabrication issues of my own.
Honda, because it's hard to look baller in your mom's Volvo.
The entire tool selection at Sears or the contents of a Snap-On truck will do you no good if you do not know how to use them.
The entire tool selection at Sears or the contents of a Snap-On truck will do you no good if you do not know how to use them.
#37
Posted 08 August 2006 - 07:55 AM
Just curious, which B20 your going with? Also, what parts/mods are you leaning towards you HP goal? Sorry I just have to question anyone else also installing a B20.
Screech
------------------------
16 Ford RS (2.3l, DS)
84 Civic 2000S (B20Z2 2.0l, SMF)
#38
Posted 08 August 2006 - 12:40 PM
actually not going to do the b20 after all, I have an ls vtec based on b18a, pr3 pistons , holley tb ,looking for itr cams and some valvetrain goodies
Edited by evilGearhead, 08 August 2006 - 12:42 PM.
#39
Posted 08 August 2006 - 12:57 PM
#40
Posted 08 August 2006 - 01:42 PM
QUOTE (evilGearhead @ Aug 8 2006, 03:52 AM)
is there a type of sandable foam or other easy to deal with substance for this purpose?
i know there is such a thing as a sandable foam that is made just for this type of thing but i have no idea where you get it. but yes, it does exist.
When I die, i want to go asleep peaceful.......... not screaming and freaking out like everyone else in the car
"i left the bar a little after you and ended up flipping my car in the arbys drive thru"
IM A LOSER!!! my car pulls harder when spinning than any "highly modified" EW
Team BUrnOUt founding member
"i left the bar a little after you and ended up flipping my car in the arbys drive thru"
QUOTE (cbstdscott @ Dec 10 2008, 03:27 PM) <{POST_SNAPBACK}>
Another loser who can not get traction. I feel sorry for him.
IM A LOSER!!! my car pulls harder when spinning than any "highly modified" EW
Team BUrnOUt founding member
#41
Posted 11 August 2006 - 02:27 AM
spray foam is sandable and can be worked with but i dont think you wanna deal with the mess it makes and there is another foam that comes in big blocks but i cant thik of the name but you can get it at hardware stores all over i believe well i can get it here and i have trouble getting anything i need for my carso im sure you can get it
My Webpage
(quote by RareCrx)HAVE A MADD TYTE DIGGITY DOGG ,BUBBLES SPRAYIN ON THE INTERCOOLER, poopin ON A 8 SECOND CHEVELLE WITH MY MINI-ME SWAP DAY..
#42
Posted 14 August 2006 - 05:53 AM
QUOTE (phatboycrxhf @ Aug 11 2006, 07:27 PM)
spray foam is sandable and can be worked with but i dont think you wanna deal with the mess it makes and there is another foam that comes in big blocks but i cant thik of the name but you can get it at hardware stores all over i believe well i can get it here and i have trouble getting anything i need for my carso im sure you can get it
isnt it that foam they make surfboards from like closed cell or something? cant quite think of the name
#43
Posted 15 August 2006 - 07:07 PM
i have the passenger side mostly done now, I discovered that I needed a new drivers side door, i just noticed today that the whole front edge was coming apart, spot welds and all. once i get that door on there I can get the side and fender mounted.
#44
Posted 15 August 2006 - 10:22 PM
i went and bought a door for $40 at a salvage yard today, it looked ok before i bought it, but once i got it home and stripped it down, i found rust under the trim at the top, and bottom, webbing damage, and bondo.
its as useless as the one i pulled off yesterday, and im out $40.
so now I still need a door before i can continue, looks like i will have to get one online, since theres no more crx salvage around here, at all.
WTB thread
its as useless as the one i pulled off yesterday, and im out $40.
so now I still need a door before i can continue, looks like i will have to get one online, since theres no more crx salvage around here, at all.
WTB thread
#45
Posted 16 August 2006 - 12:48 AM
Project looks great so far!!
So how have you found the houseman kit to install? Is it just the extra material you're having trouble with? I noticed Mr. D's purchase came with brackets....do you find much is 'missing' for you to do the body right?
I'm asking because I'm looking into getting a kit in the near future, and I'm trying to plan what I'm in for.
Keep up the updates
So how have you found the houseman kit to install? Is it just the extra material you're having trouble with? I noticed Mr. D's purchase came with brackets....do you find much is 'missing' for you to do the body right?
I'm asking because I'm looking into getting a kit in the near future, and I'm trying to plan what I'm in for.
Keep up the updates