Hi.
I want to buy a pm6 ecu.
Is yours stock? It´s with external eprom?
If so it´s myne!
Thanks
- Red Pepper Racing
- → Viewing Profile: Posts: 87zc1crxjdm
Community Stats
- Group Members
- Active Posts 81
- Profile Views 2641
- Member Title Slowpoke
- Age 48 years old
- Birthday April 9, 1976
-
Gender
Not Telling
-
Location
Portugal, Lisboa
-
Interests
Electronics, Hondas, Networking
Previous Fields
-
Drives
1987 JDM DOHC ZC-1 CRX
0
Neutral
User Tools
Friends
87zc1crxjdm hasn't added any friends yet.
Latest Visitors
Posts I've Made
In Topic: Stuff To Sell Brown Top Zc Head And Others
08 August 2005 - 02:38 PM
In Topic: Turbo Progress....
06 August 2005 - 03:33 AM
If you need help on doing the basemap and stuff i can help you.
I´ve been doing a lot of tunes for obd0/1.
Just tell me if you need.
I´ve been doing a lot of tunes for obd0/1.
Just tell me if you need.
In Topic: Suprise
05 August 2005 - 03:39 AM
The jumpers are on the top right of the burner next to the power suplly conector.
If you see carefuly you´ll have 2 jumpers that you can manipulate.
These 2 jumpers both have 3 pins.
DEpending on the pin config you have the voltage youy need.
In my case, both jumpers are like:
If you go to www.willem.org you´ll find the manuals and forum for any doubt yuou may have about willem programmer.
If you see carefuly you´ll have 2 jumpers that you can manipulate.
These 2 jumpers both have 3 pins.
DEpending on the pin config you have the voltage youy need.
In my case, both jumpers are like:
If you go to www.willem.org you´ll find the manuals and forum for any doubt yuou may have about willem programmer.
In Topic: B16a Swap To 87 Mk1
04 August 2005 - 05:22 PM
That part was cutted because it´s easier to work with the engine bay and the fitment of the turbo and all the stuff.
As we finhish the mechanics we´re going to use aliminium bar to relink it.
All the car and engine bay is going to be reinforced and there´s a roll cage comming in by my good friend.
I´m just working on the dash.
I´m using the crx i-vt one secured by an alumin frame and on the center, in front of the fuse box i´m building a panel to place all the gauges, wb, gtech and switches.
I´m locating the batery on the rear and also building a place to secure the laptop (bre and crome(after some minor changes)).
The sunroof ir all gone and an acrylic plate will be placed instead.
Plan is to squeeze most of the b16 with a t3 from a renault 21 (2.0l 185hp stock).
Expect something like 250-275hp and a nice 1/4 time.
For tires i have ready a set 13" 205 slicks.
But as street driving some 200 16" i want to use.
As we finhish the mechanics we´re going to use aliminium bar to relink it.
All the car and engine bay is going to be reinforced and there´s a roll cage comming in by my good friend.
I´m just working on the dash.
I´m using the crx i-vt one secured by an alumin frame and on the center, in front of the fuse box i´m building a panel to place all the gauges, wb, gtech and switches.
I´m locating the batery on the rear and also building a place to secure the laptop (bre and crome(after some minor changes)).
The sunroof ir all gone and an acrylic plate will be placed instead.
Plan is to squeeze most of the b16 with a t3 from a renault 21 (2.0l 185hp stock).
Expect something like 250-275hp and a nice 1/4 time.
For tires i have ready a set 13" 205 slicks.
But as street driving some 200 16" i want to use.
- Red Pepper Racing
- → Viewing Profile: Posts: 87zc1crxjdm
- Board rules
Community Forum Software by IP.Board
Licensed to: Red Pepper Racing