Sent my deposit via paypal for a kit
2
Camber Plate Kits...
Started by rpr, Oct 31 2004 10:33 PM
39 replies to this topic
#31
Posted 01 January 2005 - 09:42 PM
#32
Posted 01 January 2005 - 09:50 PM
#33
Posted 03 January 2005 - 09:58 AM
QUOTE (rpr @ Jan 1 2005, 09:50 PM)
Got it...they are looking sweet....
have you got a picture of the new chamber plates ? and are the annodized this time ?
Greetings Erwin
1. EDM 1986 Honda CRX AS - B16A1 engine - OBD1 - Turbo - Stitch welded chassis.
2. EDM 2001 Lexus IS300 3.0 RWD - Daily Drive
#34
Posted 06 January 2005 - 10:37 PM
Do these provide for any caster adjustment? Also, do you have any installed pics? I am not sure I can use them due to the current modificaton to the front strut towers.
Edited by c25ahatch, 06 January 2005 - 10:38 PM.
#35
Posted 06 January 2005 - 11:57 PM
Pics are here: http://www.redpepper...allery/strutbar
There is caster adjustment, and they will be anodized black. The final design is slightly different, but not anything major.
Tom
There is caster adjustment, and they will be anodized black. The final design is slightly different, but not anything major.
Tom
"Toby, you are a thief of joy"
#36
Posted 08 January 2005 - 11:44 PM
I remember something being said about the tops of the struts needed to be shortened a little or something, can you clarify that. I have illuminas and i dont think i can grind off the top(adjuster).
Julian
Julian
#37
Posted 09 January 2005 - 12:13 AM
Any news on the RPR strur bar? Will it be available anytime soon? I know you were still working on the design to get it to fit/work for everyone, have you made any new progress? Hopefully you're keeping the 1G integra guys in mind because I'd love to bolt one onto my RPR camber plates...
#38
Posted 09 January 2005 - 03:29 AM
QUOTE (87MugenProCR-X @ Jan 8 2005, 11:44 PM)
I remember something being said about the tops of the struts needed to be shortened a little or something, can you clarify that. I have illuminas and i dont think i can grind off the top(adjuster).
Julian
Julian
i asked the same to tom, i have koni yellow adjustable and i will have the same problem.
tom said he would measure them up for me so i can look if it will fit.
1. EDM 1986 Honda CRX AS - B16A1 engine - OBD1 - Turbo - Stitch welded chassis.
2. EDM 2001 Lexus IS300 3.0 RWD - Daily Drive
#39
Guest_-TJ_*
Posted 25 January 2005 - 04:25 PM
QUOTE (toxicshit @ Jan 9 2005, 02:29 AM)
QUOTE (87MugenProCR-X @ Jan 8 2005, 11:44 PM)
I remember something being said about the tops of the struts needed to be shortened a little or something, can you clarify that. I have illuminas and i dont think i can grind off the top(adjuster).
Julian
Julian
i asked the same to tom, i have koni yellow adjustable and i will have the same problem.
tom said he would measure them up for me so i can look if it will fit.
I have one of the last batch "prototype" set's and Tokico Illumina's as well. I'm not sure of what minor changes were made, but as they were shipped to me, they fit fine (plenty of hood clearance). I ended up shortening the top-of-the-strut spacer RPR provides in order for the strut to extend from the body further. I still have 1/8" clearance to the hood.
#40
Posted 25 January 2005 - 07:00 PM
QUOTE (toxicshit @ Jan 9 2005, 03:29 AM)
QUOTE (87MugenProCR-X @ Jan 8 2005, 11:44 PM)
I remember something being said about the tops of the struts needed to be shortened a little or something, can you clarify that. I have illuminas and i dont think i can grind off the top(adjuster).
Julian
Julian
i asked the same to tom, i have koni yellow adjustable and i will have the same problem.
tom said he would measure them up for me so i can look if it will fit.
Sorry, I did measure it, just forgot to post. I measured from the tip of the KONI adjuster thingy to the edge of the shock tower opening, and it was 46mm. Not sure what the actual clearance is to the hood from that point.
Tom
"Toby, you are a thief of joy"