Jump to content



  2. → Viewing Profile: Posts: zcrxjesse

zcrxjesse

Member Since 11 Nov 2005
Offline Last Active Nov 30 2005 01:56 AM
-----

Posts I've Made

In Topic: Lowering The Front Of My Car

21 November 2005 - 09:40 PM

QUOTE (slammin86 @ Nov 21 2005, 06:29 PM)
I saw in the FAQ that you can adjust a bolt under the front of the car and lower the front end up to .5".  I am wondering exactly where this bolt is at.  Also I would assume the car would need an allignment after this, is that correct?
What affect does doing this have on the ride and handling of the car?



the bolt is a 17mm bolt its i think the only bolt pointing down but i could be wrong. there should be a picture on this site someweres. but any who its a nut next to the torque tube. i dont really know how to explane it so look for the pic in FAQ

In Topic: Help Me Help Me

18 November 2005 - 08:48 PM

QUOTE (boman @ Nov 18 2005, 01:04 PM)
^^^ Haha, no need to get bent. lol.

-cherrypicker + levelling chain deelie
-ZC or D16A1  (1G)
-87-89 teggy transmission
-teggy half shaft
-teggy transmission and rear mount
-teggy ECU
-teggy axles and CRX axles (to make hybrids so you can retain the CRX knuckles)
-shortened custom shift linkage -- unless you dont mind having the gears a little
lower.
-teggy engine harness - or CRX Si (tighter fit)
-beer


Boom done. -- Obviously all fluids and anything else that will snap or seaze while
you're doing the swap.

j

thank you for your help that is preety much the type of answer i was looking for and i have the beer so another item off the list

In Topic: Help Me Help Me

18 November 2005 - 04:25 AM

QUOTE (jeff420 @ Nov 17 2005, 07:51 PM)
<==--found everything he needed and more using the search feature


well thank you all for your coperation... and putting up with my stupidity butt i will find what i need and i have been ofn this site a manytimes but am yet to find what i need ... but me and my 2 frinds will seek and desrtoy the zc swap.. we have bult a 95 trans am (13)seconds with a motor swap and a monte carlo also a 13 second car swap and do believe we will figure this out also. there for thank you once again and we keep the rest of you posted on the swap.. (well we have a trans am rearend to rebuild fist ..should be done in a few days.. then well talk about the important swap(the crx) and keep you posted.....o yea c diidy or what ever fuck off

In Topic: Help Me Help Me

17 November 2005 - 01:11 AM

QUOTE (C_piddy @ Nov 16 2005, 06:01 AM)
man... this web site is full of info. i don't want to write a list everytime some one gets a boner about putting in a zc... all this has been coverred and well documented... FAQ and SEARCH is your friend. Your best friend that will never sleep with your girl.

so yeah. gay thread, we get one like this every week.

chris


ya thanks its a electronic one and i know the wiring will be a bitch but its all under control.. the motors paid for and sitting here.. so there for this is not a person with a boner wishing i could do it..all i was wondering is maybee a breif explanation on the parts i would need i have motor ecu axles and tranny... so im not an o we get one of these every week person there for putt your gaurd down all i asked for was a little help.. thank you all for your help dont be an ass....

In Topic: Help Me Help Me

14 November 2005 - 11:54 PM

QUOTE (Hollowman @ Nov 14 2005, 12:29 AM)
What gen ZC?? Is it vaccum advanced ignition or electronic advance?? A few small details are needed..

Also check the articles at the top of the Swaps forum.. There are a few threads in there too..


i do believe its a 1st gen integra ZC

  1. Red Pepper Racing
  2. → Viewing Profile: Posts: zcrxjesse
  3. Board rules