i was curious so i can get some numbers from those with a d15a3 turbo. i was curious on what size turbo, the setup ur useing, and how many psi's ur running into ur engine.
im tryin to find out "if u have " " PSI's how much HP u are getting". ive been thinkin a lot about turbos, and want to find out what kind of #'s give u 6-8. 8-10, etc. im tryin to figure out what would be good for me.
i kno, its kinda on the dumb side.
1
Stupid ?'s 4 Those With D15a3 Turbo
Started by RexBoy21, May 09 2005 07:45 PM
14 replies to this topic
#1
Posted 09 May 2005 - 07:45 PM
#2
Posted 09 May 2005 - 07:57 PM
eldos running 13psi
generally speaking, it depends on what your motor has done to it.
200whp is a realistic figure on 10-12 psi tuned with a wideband.
generally speaking, it depends on what your motor has done to it.
200whp is a realistic figure on 10-12 psi tuned with a wideband.
Edited by CRXdan, 09 May 2005 - 07:59 PM.
90 crx si
13.17@113 street tires low boost
86 samurai g16 turbo
13.17@113 street tires low boost
86 samurai g16 turbo
#3
Posted 09 May 2005 - 08:45 PM
#4
Posted 11 May 2005 - 02:25 AM
QUOTE (RexBoy21 @ May 9 2005, 06:45 PM)
do u kno what other mods he has on his engine?
Stock block with modified Keihin carb ,self ported heads and a Stage2 Triflow ColtCam. 13 psi @ 7000 rpm.
Edited by eldo, 11 May 2005 - 02:27 AM.
Ed
86 Crx DX EW3 block EW2 ported head , Coltcams (nitrous/turbo Stage 2 Triflow )
T-25 with a blowthrough Keihin carb - 13 psi .
I'ma in the Carburetion Nation
86 Crx DX EW3 block EW2 ported head , Coltcams (nitrous/turbo Stage 2 Triflow )
T-25 with a blowthrough Keihin carb - 13 psi .
I'ma in the Carburetion Nation
#5
Posted 12 May 2005 - 03:26 AM
#6
Posted 16 May 2005 - 11:54 PM
#7
Posted 21 May 2005 - 04:58 AM
QUOTE (yungdriva @ May 16 2005, 08:54 PM)
what are internals????????
Internals are the pistons,rods...etc. everything in the bottem end....
#8
Posted 23 May 2005 - 07:37 AM
sorry to be rude but your use of "PSI's" is a little off. "PSI's" arent a thing its pounds per square inches so its like how much psi are you running not how many psi's. just a little constructive criticism, sorry if im a douche. haha
It runs! Carb to Megasquirt EFI.
#9
Posted 23 May 2005 - 11:39 PM
#10
Posted 24 May 2005 - 03:18 AM
id say you shoudl run 11 psi on a a stock block and see how it goes. then bump it up to 14-15.
keep a spare block handy.
keep a spare block handy.
Edited by CRXdan, 24 May 2005 - 03:19 AM.
90 crx si
13.17@113 street tires low boost
86 samurai g16 turbo
13.17@113 street tires low boost
86 samurai g16 turbo
#11
Posted 09 June 2005 - 03:21 PM
This was my buddies D15b7 at 7psi.
93 Del sol Si (PM7 pistons and just a 50shot)
85 CRX Si (underconstruction)
85 CRX Si (underconstruction)
#12
Posted 12 June 2005 - 01:33 PM
#13
Posted 12 June 2005 - 08:54 PM
well the newer d15s are puny. they shatter under boost/nos. there not nearly as tough as the older d15s
#14
Posted 14 June 2005 - 03:35 AM
QUOTE (rexsk8er @ Jun 12 2005, 06:54 PM)
well the newer d15s are puny. they shatter under boost/nos. there not nearly as tough as the older d15s
I fully agree to that. 116 shots or 13 lbs boost and lots of backfires from leaning out and its still living.
Ed
86 Crx DX EW3 block EW2 ported head , Coltcams (nitrous/turbo Stage 2 Triflow )
T-25 with a blowthrough Keihin carb - 13 psi .
I'ma in the Carburetion Nation
86 Crx DX EW3 block EW2 ported head , Coltcams (nitrous/turbo Stage 2 Triflow )
T-25 with a blowthrough Keihin carb - 13 psi .
I'ma in the Carburetion Nation
#15
Posted 14 June 2005 - 10:54 AM
QUOTE (RexBoy21 @ Jun 12 2005, 02:33 PM)
Del sol S
93 Del sol Si (PM7 pistons and just a 50shot)
85 CRX Si (underconstruction)
85 CRX Si (underconstruction)