just broke some stuff on my crx so cant afford the zc any more, so i decided to turbo my ew, what manifold woeks, or do i use my original one? i will be using a t2 turbo, pushing about 10-12 psi would that be ok on the ew since it has low compression anyways?
0
Turbo Ew
Started by panda, Feb 02 2005 08:20 PM
8 replies to this topic
#1
Posted 02 February 2005 - 08:20 PM
#2
Posted 02 February 2005 - 08:40 PM
do a search but you need an hf manifold from either a 3rd gen civic or first gen crx and 8psi is as high as you need to go as i recall on stock internals,for the manifold you have to make an adpter though to fit the turbo
Edited by NiMi1718, 02 February 2005 - 08:40 PM.
#3
Posted 02 February 2005 - 09:32 PM
QUOTE
do a search but you need an hf manifold from either a 3rd gen civic or first gen crx and 8psi is as high as you need to go as i recall on stock internals,for the manifold you have to make an adpter though to fit the turbo
psi should be relative to the size of the turbo you are using. dont worry about how much you are boosting just as long as you keep hp levels below 220whp (on a really good tune!!) anywhere past that hp and youre just asking to break things in your stock bottom end.. your stock map will be the limiting factor since it only reads 10-11psi.
Edited by rextec, 02 February 2005 - 09:34 PM.
#4
Posted 03 February 2005 - 07:55 PM
#5
Posted 03 February 2005 - 08:21 PM
#6
Posted 03 February 2005 - 08:43 PM
if you have the si you will have to get either a dx or a hf manifold. to make an adapter you get a 3/4 or 1 inch plate, trace the manifold gasket out and cut it out and drill the holes and counter sink the holes, than copy the turbo gasket on the other side and counter sink the holes. that way the bolt heads are flush. but you dont want your bolt holes near the gasket or you may leak exhuast.
Sean
Sean
#7
Posted 04 February 2005 - 07:29 PM
what gen manifold, third or fourth gen?
any one know how to hook up the water lines and oil lines?
what do i need to do the lines?
and where on the oil pan do i put the drain line?
any one know how to hook up the water lines and oil lines?
what do i need to do the lines?
and where on the oil pan do i put the drain line?
#8
Posted 05 February 2005 - 02:00 PM
4th gen has the newer d series, it would require the 84-87 civic or crx carbed manifold.
You hook the oil feed to a tee on the oil pressure line and the oil return you have to drill a hole in the oil pan, as far up on the pan as possible. that way it wont be restricted because of the oil levle is above the return
The water lines you have to hook up to the t/b coolant lines, you dont really need them on the t/b unless it gets real cold
Sean
You hook the oil feed to a tee on the oil pressure line and the oil return you have to drill a hole in the oil pan, as far up on the pan as possible. that way it wont be restricted because of the oil levle is above the return
The water lines you have to hook up to the t/b coolant lines, you dont really need them on the t/b unless it gets real cold
Sean
#9
Posted 05 February 2005 - 09:53 PM
1/2" is more than adequate. anything bigger and you may run itnto problems such as the turbo sitting too low, affecting the oil drains function.
Edited by CRXdan, 05 February 2005 - 09:54 PM.
90 crx si
13.17@113 street tires low boost
86 samurai g16 turbo
13.17@113 street tires low boost
86 samurai g16 turbo