B Series Swap Wiring Chart

From RPRWiki

Jump to: navigation, search




ECU WIRING TABLE for OBD0 B-series motors into 85-87 CRX/CIVIC Si




As compiled by 87sivtec

85-87 CRX/Civic Si ECU

89-91 PR3/PW0 JDM ECU
Pin # Description
Pin # Description Notes
A1 #1 Injector (Brown)
A1 #1 Injector (Brown)
A2 Ground (Black)
A2 Ground (Black)
A3 #2 Injector (Red)
A3 #2 Injector (Red)
A4 Ground (Black)
A4 Ground (Black) Connects to Black Ground on Main Relay
A5 #3 Injector (Red/Black)
A5 #3 Injector (Lt. Blue)
A6 Ground (Black)
A6 Purge cut off valve (Blue) Don't need
A7 #4 Injector (Yellow)
A7 #4 Injector (Yellow)
A8

A8 Vtec Solenoid (Green/White) Add This.
A9

A9

A10

A10 Pressure Regulator Cutoff valve Don't need
A11

A11 IACV/EACV (Blue/Yellow) Add This.
A12 Main Relay (Green/Blue)
A12 Main relay (Green/Black) Connects to Green/Black on main relay
A13 12V Ignition
A13 12V Ignition (Yellow/Black) Joins A15
A14 Main Relay
A14 Main relay Joins A12
A15 12V Ignition (Yellow/Black)
A15 12V Ignition (Yellow/Black) From main relay. Also powers injectors and IACV.
A16 Ground (Brown/Black)
A16 Ground (Brown/Black)
A17 12V (White/Green)-from fuse 10
A17

A18 Ground (Black/Red)
A18 Ground (Black/Red)






B1

B1 Main Fuse Box (White/Green) From Hazard Fuse
B2

B2

B3

B3 A/C clutch relay (yellow) You're good if you need this!
B4 Fast idle control solenoid (Green/Yellow)
B4

B5

B5 VTEC Oil Pressure switch (Blue/Black)
B6 Check engine light (Green/Orange)
B6 Check engine light (Green/Orange)
B7

B7

B8 A/C Switch (Brown/Red)
B8 A/C Switch (Blu/Red)
B9

B9

B10

B10 Crank angle sensor (Orange)
B11

B11 Defogger switch (Black/Green)
B12

B12 Crank angle sensor (White)
B13 Ignition Switch (Brown/White) - From main relay
B13 Ignition Switch (Brown/White) From Main Relay and No. 2 Fuse.
B14 Alternator Input (White/Red)
B14 Alternator input (blue)
B15

B15 Ignitor Joins B17 - both go to ignitor
B16

B16 VSS (yellow/red) Add this Or VTEC will NOT work.
B17 Purge cutoff solenoid valve (Red/White)
B17 Ignitor Joins B15 - both go to ignitor
B18

B18

B19

B19

B20 IMA-idle mixture adjustment sensor (white/yellow)
B20 Ignition timing adjustment connector (Brown) Gets grounded to set ECU into adjustment mode






C1 #1 CYL sensor (orange changing to red)
C1 #1 CYL sensor (Blue/Green)
C2 #1 CYL sensor (Blue/Yellow)
C2 #1 CYL sensor (White)
C3 TDC sensor (orange/blue changing to Brown)
C3 TDC sensor (orange/blue)
C4 TDC sensor (white/blue changing to Blue)
C4 TDC sensor (white/blue)
C5 Intake air temp (Red/yellow)
C5 TA sensor - Intake temp (red/yellow)
C6 Watertemp (red/white)
C6 TW sensor - water temp (red/white)
C7 Throttle angle sensor (red/blue)
C7 Throttle angle sensor - TPS (red/blue)
C8

C8 O2 #2 (red/blue changing to orange)
C9 PA sensor (red)
C9

C10

C10 Brake switch (green/white)
C11 MAP sensor (white)
C11 MAP sensor (white)
C12 Ground (Brown/Black) used for TPS,TW,PA,IMA
C12 Ground (green/white changing to green) Joins ignition timing connector, TW ,TPS, TA
C13 Throttle angle , PW, IMA (yellow/red)
C13 Throttle angle sensor - TPS (yellow/white)
C14 MAP sensor (brown/white)
C14 MAP sensor (green/white)
C15 MAP sensor (red)
C15 MAP sensor (red/yellow)
C16 O2 sensor (white)
C16 O2 #1 (White)







Please Note, I have tried to be as accurate as possible, but there may be some errors.


Pictures of OBD0 Plugs Can Be found here --->[[1]]





Personal tools