17 replies to this topic

[Mark L]

Hello, 
I sold my 89 Integra today. I need to sell of my spares and assorted parts.
 
I will start taking inventory tomorrow and add some pics, but will start a list to generate some interest. I will be adding prices.
 
89 d16a1 longblock. I was ice racing and lost power. I think the head gasket blew.  I swapped to another engine and stored this. There is no distributor. There is a bare stock intake manifold. This engine was using a bit of oil before it failed. This a good for a rebuild.
All parts do not include shipping  from 12580.
 
CG 86-89 Trans. I had this for a backup.
 
Stock Flywheel
 
Tokico Blue 
Rear set  Tokico Iluminas 
1987 Teg d16a1 Oil Pan click link below.
http://www.redpepper...ndpost&p=569271
 
1986 Civic Combination switch
Click link below
http://www.redpepper...ndpost&p=569272
 
 
Set of 1G Integra knuckles. 50 bucks.


 
 
 
 
I have most of the rear suspension including the beam. I should be able to make up a rear disk swap kit.
I also have the Rear Integra trailing arms. Pics coming
 
 
Blacktop ZC camshafts, 34 tooth cam gears, 17 tooth crank gear, and a brand new Gates Blue timing belt. The belt was 60 alone. $200 plus shipping

inu
 

[Vicious]

I want te lcas

[Mark L]

Lower Arms sold 5 minutes after posting.

[Mrfixit]

Do you have a rear engine mount for the d16a1?

[Dirtcircle86]

Am I correct in recalling the 17 tooth ZC crank gear will not fit a D16A1 crank?  If it does fit, I'm in for the cams, gears and belt.  Actually, I already have an A1 crank at the machine shop so I could have it turned down if the A1 has a larger shout. 

[Mark L]

 

Am I correct in recalling the 17 tooth ZC crank gear will not fit a D16A1 crank?  If it does fit, I'm in for the cams, gears and belt.  Actually, I already have an A1 crank at the machine shop so I could have it turned down if the A1 has a larger shout. 

 

 

I will be at the garage tomorrow. I will measure the ID and let you know.

[3rd gen sinner]

The A1 has two different size crank snouts. The 86/87 has a smaller snout than the 88/89. The corresponding year ZC crank gear should be the same.


Sent from my iPhone using Tapatalk

[Mark L]

The A1 has two different size crank snouts. The 86/87 has a smaller snout than the 88/89. The corresponding year ZC crank gear should be the same.

 

 

Just measured it and it is 24 mm. blacktop/88-89

[Mark L]

 

 87 integra oil pan $20 

 

 

Rear Tokico blues. Actually I should say blue because one does not have near the damping as the other.  I could send one of both, your choice. $30

Rear Tokico Iluminas. Nice and clean low mileage. $150

 

 

 

 

 

 

Shipping from 12580 is not included.

[Mark L]

86 Civic DX Combination switch $25. This does not have the rear wiper switch for the SI.

 

 

 

 

ippin

 

Shipping from 12580 is not included.

[Mark L]

Updated first post with Pictures.

[Mark L]

Do you have a rear engine mount for the d16a1?

No.

[gtpilot]

Mark,

 

Any chance you have the intermediate shaft and mounting bracket?

 

Kitk

[Mark L]

i am on vacation in Maine and will be back Monday. I will deal with the shipping quotes then... Thanks!

Mark.

[JEA86]

Dibs on the hubs