Jump to content




K Swap Knowledge Dump


  • You cannot reply to this topic
37 replies to this topic

#31
Mag00n

  • Slowpoke
  • PipPip
    • Group: Members
    • Drives: 1998 Integra Type R
Well Im going to have to Have the runners on the exhaust manifold extended about an inch to clear the subframe..being that the k24 is taller Id expect youll have to do the same..but that also depends on the height and lean of Brians mounts

#32
CSPCRX

  • Leadfoot
  • PipPipPipPipPip
    • Group: 2016 Contributor
    • Location:Phoenix AZ
    • Drives: B Powered 86 CRX SI, 2012 Audi S4, 07 Harley FXST Softail
    • Image Gallery
    Garage View Garage

Thanks for sharing. That is true, how the motor sits will greatly impact the angle of the header.

 

i am still waiting on lots of parts so I’m watching your build closely for learnings. I’m also thinking I may have to run the K-tuned water filler that is up near the valve cover.

 

Finally got an update on some OEM parts I ordered. Mostly maintenance items like front and rear main seals, VTEC screens, etc. stuff that’s easy to replace now and a pain later. 


Victor
86 B-Powered CRX SI (SMF Solo2, HPDE-4 NASA & TA-A Time Attack
07 Harley FXST Softail
12 Audi S4

#33
Mag00n

  • Slowpoke
  • PipPip
    • Group: Members
    • Drives: 1998 Integra Type R
Id recommend the tract tuff filler neck ..top notch quality

#34
CSPCRX

  • Leadfoot
  • PipPipPipPipPip
    • Group: 2016 Contributor
    • Location:Phoenix AZ
    • Drives: B Powered 86 CRX SI, 2012 Audi S4, 07 Harley FXST Softail
    • Image Gallery
    Garage View Garage

I’ll look into it


Victor
86 B-Powered CRX SI (SMF Solo2, HPDE-4 NASA & TA-A Time Attack
07 Harley FXST Softail
12 Audi S4

#35
CSPCRX

  • Leadfoot
  • PipPipPipPipPip
    • Group: 2016 Contributor
    • Location:Phoenix AZ
    • Drives: B Powered 86 CRX SI, 2012 Audi S4, 07 Harley FXST Softail
    • Image Gallery
    Garage View Garage

Had to go to they junk yard and visit the accord I took the TB from. Not to anyone else using a JDM K24a when you get the TB from the Accord also get the two studs out of the manifold. The drive by wire TBs are thicker so therefore the two studs are longer.


Victor
86 B-Powered CRX SI (SMF Solo2, HPDE-4 NASA & TA-A Time Attack
07 Harley FXST Softail
12 Audi S4

#36
LoneWolf

  • Granny
  • Pip
    • Group: Members
    • Location:Fort Worth
    • Drives: 87 Civic Wagon
    Garage View Garage

Good to see some other folks working on K Swaps in this chassis.  Here's my 87 Wagon AWD project.  Currently waiting on a K Pro to come in, then its turbo time!image_url-11225-1593878069.jpg


Edited by LoneWolf, 04 July 2020 - 11:00 AM.


#37
CSPCRX

  • Leadfoot
  • PipPipPipPipPip
    • Group: 2016 Contributor
    • Location:Phoenix AZ
    • Drives: B Powered 86 CRX SI, 2012 Audi S4, 07 Harley FXST Softail
    • Image Gallery
    Garage View Garage

Sweet, sounds like it’s going to be a ripper! Tell us about your motor and setup.

 

whats the coating on the intake manifold?


Victor
86 B-Powered CRX SI (SMF Solo2, HPDE-4 NASA & TA-A Time Attack
07 Harley FXST Softail
12 Audi S4

#38
Mag00n

  • Slowpoke
  • PipPip
    • Group: Members
    • Drives: 1998 Integra Type R

Good to see some other folks working on K Swaps in this chassis.  Here's my 87 Wagon AWD project.  Currently waiting on a K Pro to come in, then its turbo time!image_url-11225-1593878069.jpg

 

Did you adapt hasport EF mounts?