Jump to content




B And D Series Torque Specifics


  • You cannot reply to this topic
1 reply to this topic

#1
codyz0r

  • Professional Person
  • PipPip
    • Group: 2011 Contributing Member
    • Location:Harrison Township MI
    • Drives: 1992 F22 Prelude - Parting out the REX :'(
To find something specific, type CTRL+F and use the "Find" function for quicker answers. Please PM me if you would like to add or edit this page.

ALL TORQUE SPECS ARE IN FT-LB.
Just a little FYI 1 FT/LB equals 12 IN/LB, so if you want to use a beam type wrench which are almost all IN/LBS take your FT/LBS and multiply by twelve to get IN/LBS. This is good to know because for any bolt requiring 20 ft/lbs or below, you should convert to in/lb because it's a little more accurate. Also when tightening bolts that you absolutely, positively do not want to break such as cam cap bolts whether its for B or D series, you should use a beam type torque wrench with IN/LBS and NOT a clicker type torque wrench which are usually FT/LBS.

B Series Torque Specs


Key-
Teg=Integra
Anything that does not say "(all B series)" next to it can only be guaranteed for B series Integra only.

CYLINDER HEAD BOLT TORQUE SPECS (tightening) / (loosening)

8, 4, 2, 6, 10 <---intake order 3, 7, 9, 5, 1
7, 3, 1, 5, 9 <---exhaust order 4, 8, 10, 6, 2

Torque in steps: 22ft-lbs (264in-lbs), Then to 63ft-lbs (756in-lbs) (final spec) 94+ Teg
Torque in steps: 22ft-lbs (264in-lbs), Then to 61ft-lbs (732in-lbs)(final spec) 90-93 Teg / B16's


CAMSHAFT COVER SPECS
13, 9, 5, 1, 3, 7, 11 (side of cam cover closest to intake)
14, 10, 6, 2, 4, 8, 12 (side of cam cover closest to exhaust)

Shown above is one cam cover, sequence is the same for intake and exhaust cam cover.

#1-10 20ft-lbs (240in-lbs) #11-14 7.2ft-lbs (86in-lbs) (94+ B18C specs)
#1-10 16ft-lbs (192in-lbs) #11-14 8ft-lbs (96in-lbs) (B16A specs)
**not sure what the specs are for non-VTEC motors, sorry**

Seat each camshaft by pushing it towards the dizzy side of cylinder head.

VALVE COVER SPECS

7______________5______(Intake side of valve cover)
_____3____1____
_____4____2____
8______________6______(Exhaust side of valve cover)

7.2 ft-lbs (86in-lbs) (all B series)

FLYWHEEL TORQUE SPECS
_______1
_____6___8
___4_______3
_____7___5
_______2

Torque in steps: 19ft-lbs (228in-lbs), 38ft-lbs (456in-lbs), 57ft-lbs (684in-lbs), Then to 76ft-lbs (912in-lbs) (all B series)

PRESSURE PLATE TORQUE SPECS

_______1
_____6___3
_____4___5
_______2

Torque in steps: 5ft-lbs (60in-lbs), 10ft-lbs (120in-lbs), 14ft-lbs (168in-lbs), Then to 19ft-lbs (228in-lbs) (all B series)

FUEL FILTER BANJO BOLT
25ft-lbs (300in-lbs) (94+ Teg specs)
16ft-lbs (192in-lbs) (90-93 Teg / B16 / 89-91 Civic CRX specs)

FUEL FILTER SERVICE BOLT
11ft-lbs (132in-lbs) (94+ GSR specs)
9ft-lbs (108in-lbs) (90-93 Teg / B16 / 89-91 Civic CRX specs)

HEADER A-PIPE TO B PIPE (x3)
40ft-lbs (480in-lbs) (all B series)

B PIPE TO CAT (x2)

12ft-lbs (144in-lbs) (all B series)

SHIFT LINKAGE EXTENSION ROD TO TRANNY BOLT (8x1.25mm)
16ft-lbs (192in-lbs) (90+ Teg specs)
12ft-lbs (144in-lbs) (B16 specs)

SPEED SENSOR TO TRANNY BOLT
9ft-lbs (108in-lbs)

ALTERNATOR TOP BOLT
17ft-lbs (204in-lbs) (all B series)

ALTERNATOR BOTTOM BOLT
33ft-lbs (396in-lbs) (all B series)

CRANKPULLEY BOLT
130ft-lbs (1560in-lbs) (90+ Teg)

If the crankpulley bolt is new:
145ft-lbs (1740in-lbs) loosen it a little, then re-tighten to 130ft-lbs (final spec)

87ft-lbs (1044in-lbs) (B16A, first gen)
**not sure what torque is for B16A2 and B16A3's**

TIMING BELT TENSIONER

40ft-lbs (480in-lbs) (all B series)

DRIVER SIDE BRACKET TO BLOCK (x3)
40ft-lbs (480in-lbs) (all B series)

DRIVERS SIDE BRACKET STUD & BOLT

54ft-lbs (648in-lbs) (all B series)

DRIVER SIDE ENGINE TO CHASSIS MOUNT BOLT
40ft-lbs (480in-lbs) (all B series)

TRANNY MOUNT TO TRANNY BOLTS (x3)
54ft-lbs (648in-lbs) (all B series)

TRANNY MOUNT TO CHASSIS BOLT

40ft-lbs (480in-lbs) (all B series)

REAR ENGINE BRACKET TO TRANNY BOLTS (x3)
43ft-lbs (516in-lbs) (1 passenger side) 86.8ft-lbs (1041in-lbs) (2 driver side) (94+ Teg specs)
43ft-lbs (516in-lbs) (90-93 Teg / B16 specs)

REAR ENGINE BRACKET TO MOUNT BOLT
43ft-lbs (516in-lbs) (all B series)

REAR MOUNT TO REAR SUBFRAME BOLTS (x3)
43ft-lbs (516in-lbs) (all B series)

TRANNY TO BLOCK BOLTS (x5)
47ft-lbs (564in-lbs) (all B series)

LONG AND SHORT STARTER BOLTS

33ft-lbs (396in-lbs) (all B series)

CLUTCH COVER LOWER BOLTS (8mm)
17ft-lbs (204in-lbs) (all B series)

CLUTCH COVER UPPER BOLTS (6mm)

9ft-lbs (108in-lbs) (all B series)

INTERMEDIATE SHAFT TO BLOCK BOLTS (x3)
28ft-lbs (336in-lbs) (all B series)

FRONT AND REAR STIFFENER TO TRANNY BOLT
42ft-lbs (504in-lbs) (all B series)

FRONT AND REAR STIFFENER VERTICAL BOLTS

17ft-lbs (204in-lbs) (all B series)

INTAKE MANIFOLD BOLTS
17ft-lbs (204in-lbs) (all B series)

EXHAUST MANIFOLD BOLTS
23ft-lbs (276in-lbs) (all B series)

BALL JOINT CASTLE NUT
40ft-lbs (480in-lbs)

LCA TO DAMPER FORK LOWER NUT
47ft-lbs (564in-lbs)

DAMPER FORK UPPER BOLT
32ft-lbs (384in-lbs)

32mm AXLE SPINDLE NUT
134ft-lbs (1608in-lbs)

OIL DRAIN PLUG
33ft-lbs (396in-lbs) (all B series)

TRANNY FILL PLUG

33ft-lbs (396in-lbs) (all B series)

TRANNY DRAIN PLUG
29ft-lbs (348in-lbs) (all B series)

SPARK PLUGS
20ft-lbs (240in-lbs)

D Series Torque Specs


Auto Tranny Drain plug.........................29
Manual Tranny Drain and fill plug..........30-40
Wheel Lug Nuts....................................80
Fuel Filter
Banjo Bolt............................................16
Service Bolt.........................................9
Clamp Bolt...........................................9

Valve cover Bolts...................................7
Spark Plugs..........................................13
Cam Gear Bolt.......................................27
Cam cover crown nuts.............................7
Crank(vibration) damper bolt.................119
Cylinder Head Studs....................1st step..22...2nd..49
Flywheel Bolts M/T................................76
Drive Plate bolts for A/T........................54
Header Bolts to Cylinder Head................22
Header to downpipe bolts.......................33
Intake Manifold Bolts..............................16
Oil Pan bolts...........................................9
Oil pick up tube bolts..............................17
Oil Pump to engine block bolts/nuts...........9
Oil Pump Screen bolts..............................8
Oil pump cover Screws.............................5
Oil filter Housing Bolts..............................9
Rocker arm shaft pedestal bolts................16
Rocker arm shaft end caps bolts................9
Timing belt adjustment bolt.........................31
Rod Bolts.................................................23

Main Bearings cap bolts
Separate caps and bridge..........................48
One piece cap assembly............................33
Water pump pulley bolts.............................9
Thermostat housing bolts............................9
Water pump attaching bolts.........................9

Fuel injection service bolts
88-90.......................................................9
91up.........................................................11
Throttle Body nuts.....................................16
Fuel Rail nut..............................................9

Manual Transmission
Countershaft locknuts................................65
End cover bolts.........................................9
Selector arm holder bolts...........................9
Tranny case to Flywhee housing..................20
Tranny to engine bolts
4 speed.....................................................33
5 speed.....................................................50
Clutch pressure plate bolts...........................19
Release fork bolts........................................22
Driveaxle/hub nuts.......................................134

Brake hose to caliper banjo bolts (front/Rear)..25
Master Cylinder Mounting nuts.......................11
Brake Booster mounting nuts.........................9



#2
badpenny

  • tinker, tinker....BOOOOOOM!!!! then I run around
  • PipPipPipPipPipPip
    • Group: Contributing Mod
    • Location:Hurst, Texas
    • Drives: Don't, because they don't run and I am a crappy mechanic.
    • Image Gallery
    Garage View Garage
this really needs to get into the wiki
Honda, because it's hard to look baller in your mom's Volvo.Posted Image 
The entire tool selection at Sears or the contents of a Snap-On truck will do you no good if you do not know how to use them.