Jump to content




Project "cahitapower"


  • You cannot reply to this topic
68 replies to this topic

#1
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si

BUILD RESURRECTION! LOTS OF UPDATES COMING!

 

Hey everyone, I've been a member for quite sometime. I figure its time for me to start my own build thread on my 3gen.

I first got my 3gen about 4yrs ago, almost for 17th birthday. I used to work part time and saved every penny for one. I got a deal (sort_of ) on it and bought the car from this guy for 350 bucks, but the hatch wasn't pretty. It was missing the driver rear side glass, the bumpers were all hanging, front windshield cracked badly, the hatch was a mess but i deeply like these civics so i did not think twice to buy it.Then found an 88' Integra which i bought as a donor for the 3gen. It slept at my friend's garage for all this time. Now its time to build it and make my mark on RPR with yet another regular build on here, but then again what is a regular build on this wonderful/amazing website, lol .

Hope you guys enjoy and help me with some advice as i proceed putting together my 3gen, feel free to post any ideas, thoughts, or comments.


Set Up:(so far) Still in Boxes or garage kept

Engine:
-D16A1 (88-89 version)
-Port/Polished Head
-JGE Dual Strings and Retainers
-Custom JG Forge Pistons (11.8 compression)
-Eagle H Beam Rods
-Polished Crank Journals
-Ported intake Manifold
-Shuck2 Single Cam Intake Manifold and ZCspeed adapter plate
-63mm Throttle body
-AEM Fuel Rail

 

 

Transmission:
-JDM ZC Transmission

-OBX Helical LSD
-AASCO 8pound flywheel
-CenterForce Double Sided Clutch,
-Chedda_J Adjustable Short shifter
-1 to 4th gear Carbon Synchros
-Accord 5th gear


Suspension/Steering:
-Tokico 5way Adjustable
-Ground Control Rear Strings
-Tien Medieval Pro
-Addco F/R Sway Bars
-Heeltoe Caster/Camper Plate
-Firstgencrx Bump Control
-Firstgencrx PanHard Bar
-Engery Suspension Master Bushing Kit(Red)
-Cusco F/R Strut Bars
-JEM Motorsports B/C Piller Bars
-Custom Lower B Piller Bar


Brakes
-Front&Rear Integra Brake Conversion
-GoodRidge Brade brake lines
-JDM 86-89 Front Accord Calipers (Double pistons)


JDM Goodies/Accessories/Interior:
-RHD Conversion
-JDM Blackhousing Headlights
-JDM Corner Lights
-JDM Rear Lights
-JDM ZC Hood
-JDM 3piece Lip
-Center Arm Rest
-Sun Shade Panel/ and Bag
-Roof Visor
-1gen Integra Front Sits
-JDM Rear Seats
-Radio Delete Panel
-Rear Speaker Panels
-NZ Brand Rear Wing


What's Next On My List :
-BisiMoto V2 Header for D16
-27.5mm Torsion Bars
-Getting the RHD Convserion done.....



Here's a pic when i first got it and fixed it up abit made it look like a car lol ....
Picture004.jpg


So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#2
Frank

  • Slowpoke
  • PipPip
    • Group: Members
    • Location:colorado
    • Drives: 86 crx si
I would LOVE to see the car after the RHD conversion is completed.
Bam! Behold, a public bulletin board, built of both brilliance and barbarity by bastards with boners. This bastion, no mere bulwark of boredom, is a brutal barrage of blistering bullshit, barely benevolent...A brotherhood of blasphemy, blessed with more balls than brains, battling the bland, the bogus, the benign. Bedlam? Bring it on. But I babble... better to be brief. We are /b/.


#3
E-Man

  • Speedy
  • PipPipPipPip
    • Group: 2014 Contributor
    • Location:Long Island, NY
    • Drives: 1985 CRX Si, 2004 Subaru FXT
Glad to hear you got the rhd clip Franky and that your project is underway. J-Man and I are just around the corner if you need spare hands.

Us Queens boys have to stay together!

Elliot
Posted Image

#4
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
QUOTE (Frank @ Nov 14 2010, 05:06 AM) <{POST_SNAPBACK}>
I would LOVE to see the car after the RHD conversion is completed.


Its going to be a few till i send it to get the converted with the holidays coming and all but should have it done by the month of January. Stay tuned in!

QUOTE (E-Man @ Nov 14 2010, 09:02 AM) <{POST_SNAPBACK}>
Glad to hear you got the rhd clip Franky and that your project is underway. J-Man and I are just around the corner if you need spare hands.

Us Queens boys have to stay together!

Elliot


HEYY Elliot ...happy to hear i got extra hands to help out. Right back at you, like you said Us Queens boys got to stay together.. cool.gif
So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#5
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
Here's a shot when i drove it before it was put apart and stored for 4yrs.... cool.gif


So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#6
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
Here is a shot at my suspension set up that i will be using to take out the 3gen Si...




I also got the the Tien MP..but i wont be using them till i put some miles on the car..here's a glimpse



Still need Torison bars...should be getting them pretty soon.. wink.gif
So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#7
darkstar42

What are you going to do with the car when its all done, Road race ,Drag, Show it off are you going to dyno it what are you expecting for hp?? I built mine trying to keep all parts factory honda parts as far as the motor goes but i going to get crazy ang go full drag i want low 13s all motor. your project sound cool kept it up!!!

#8
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
QUOTE (darkstar42 @ Nov 17 2010, 02:08 PM) <{POST_SNAPBACK}>
What are you going to do with the car when its all done, Road race ,Drag, Show it off are you going to dyno it what are you expecting for hp?? I built mine trying to keep all parts factory honda parts as far as the motor goes but i going to get crazy ang go full drag i want low 13s all motor. your project sound cool kept it up!!!



Hey thanks...I'm leaning on more of a road race car/drag(even tho i will have to be changing the setups) but i think it will be capable of completing on a show ...on the d16a1 i'm praying to hit 200hp All Motor, but i will be more then happy with 180...i will be dyno it when tuning it, I'm going to be running hondata S300 on a p28...but then again the motor is going to come out in the future and will be getting replaced with one that is more modern ph34r.gif ...on full slicks and gutted out i expect to hit mid 13 but if it does less den that, I'll be having a face like dis guy -> biggrin.gif ..lol... but on the bottle i expect to hit 12's lets see what happens...
So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#9
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
Getting a feel of of it...lol laugh.gif


So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#10
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
havent done much...about to move the clip and a few parts to the garage were the 3gen sleeps will be starting soon..

So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#11
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
hey all,
i finally got the clip and the car all in one location (finally got my dad off my back now that the big box isn't in his garage.. tongue.gif )..any how, next step is to get it converted and then assemble the motor...

I figured since i started posting up my suspension set up, guess i would start from there (Suspension & Steering)...









Yeaa all i could do now is just imagine how my 3gen is going to drive.. ph34r.gif
So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#12
SHOGUNOVDDRK

  • Leadfoot
  • PipPipPipPipPip
    • Group: Members
    • Location:Australia
    • Drives: 1986 civic hatchback
QUOTE (cahitapower @ Dec 15 2010, 04:56 PM) <{POST_SNAPBACK}>


Pump steer kit..?


Best of luck.
QUOTE(SHOGUNOVDDRK;835304)
the import scene has kinda become like emo's.... its killing itself whilst looking overdressed and in drag




QUOTE(phyregod;835835)
Sig worthy. But mine is full.


#13
OG Wagon

  • Leadfoot
  • PipPipPipPipPip
    • Group: 2009 Contributing Member
    • Location:Mooresville, NC
    • Drives: 1986 Crx Si
WOW! This thing looks like it is going to be SERIOUS.

Sweet build. Certainly in for progress. Way to go all out, keep it up!

- DT


WagoCats HOOOOOOOO!!!!!

#14
cahitapower

  • In the left lane
  • PipPipPip
    • Group: 2010 Contributing Member
    • Location:Queens, NewYork
    • Drives: 1986 civic si
QUOTE (SHOGUNOVDDRK @ Dec 15 2010, 01:51 AM) <{POST_SNAPBACK}>
Pump steer kit..?


Best of luck.


yup it sure is..firstgencrx products...they look really good..

thanks..
So MuCh In SUcH A SmALL BoX

Project Build "CahitaPower"

#15
Old School REX

  • ホンダ、夢の力
  • PipPipPipPipPip
    • Group: 2012 Contributor
    • Location:Nashville TN.
    • Drives: -------- 1986' CRX Si (X2) -------- 1993' GMC Sanoma SLE
    • Image Gallery
I think he meant spelling error... you said pump... its bump. lol