Jump to content




Parting Out An 86 Crx


  • You cannot reply to this topic
6 replies to this topic

#1
jwr914

  • Slowpoke
  • PipPip
    • Group: Members
    • Location:Houston, Texas Area
    • Drives: Street: S2k Races: HP Honda + CF/FF 1972 Crosle 25 + RT4 based CSR
Like it says, I'm using a pretty nice CRX for a parts car. The interior is not needed, the car is for club race spare parts so everything other than running gear can go. Anyone needing dash, etc. should let me know before it hits the dumpster.

You can contact me at [email protected]

James

James Rogerson
84-87 Civic SCCA HP
2006 S2k daily driver

#2
zakats

  • 1980's birth control, brought to you by Honda.
  • PipPipPipPipPipPip
    • Group: 2014 Contributor
    • Drives: The work car, way more than I'd care to admit
    Garage View Garage
Location, Location, Location!
He who dies with the most toys, wins.

#3
Lymitliss

  • King Luke
  • PipPipPipPipPip
    • Group: 2012 Contributor
    • Location:Seattle, Wa
    • Drives: 1986 CRX Si B18C1, 1973 240Z V8 Conversion
    Garage View Garage
I'm assuming it's not an Si...
Build Thread- Here


#4
badpenny

  • tinker, tinker....BOOOOOOM!!!! then I run around
  • PipPipPipPipPipPip
    • Group: Contributing Mod
    • Location:Hurst, Texas
    • Drives: Don't, because they don't run and I am a crappy mechanic.
    • Image Gallery
    Garage View Garage
houston
Honda, because it's hard to look baller in your mom's Volvo.Posted Image 
The entire tool selection at Sears or the contents of a Snap-On truck will do you no good if you do not know how to use them.

#5
jwr914

  • Slowpoke
  • PipPip
    • Group: Members
    • Location:Houston, Texas Area
    • Drives: Street: S2k Races: HP Honda + CF/FF 1972 Crosle 25 + RT4 based CSR
You'd be assuming wrong. It's an Si. I bought it simply for the intake manifold. I'll probably only keep the front hubs and a few other bits.

I also have a bolt in AutoPower roll bar system for a 84-87 Civic that I need to get out of the garage. Two ew motors and transmissions. I was going to make this car a NASA car for my son, but bought a Subaru STi already built car instead. (It's cheaper than building a new Honda) ;-)

QUOTE (Lymitliss @ Jul 22 2009, 04:08 AM) <{POST_SNAPBACK}>
I'm assuming it's not an Si...



James Rogerson
84-87 Civic SCCA HP
2006 S2k daily driver

#6
jwr914

  • Slowpoke
  • PipPip
    • Group: Members
    • Location:Houston, Texas Area
    • Drives: Street: S2k Races: HP Honda + CF/FF 1972 Crosle 25 + RT4 based CSR
All the engine stuff is gone except for a JDM carb I forgot to give to Zak and if he wants it he knows where it is. I didn't get pictures for the Si molding and it'll have to wait until after the SCCA runoffs. I fly out tomorrow and will not be back for two weeks.



QUOTE (jwr914 @ Sep 11 2009, 09:13 AM) <{POST_SNAPBACK}>
You'd be assuming wrong. It's an Si. I bought it simply for the intake manifold. I'll probably only keep the front hubs and a few other bits.

I also have a bolt in AutoPower roll bar system for a 84-87 Civic that I need to get out of the garage. Two ew motors and transmissions. I was going to make this car a NASA car for my son, but bought a Subaru STi already built car instead. (It's cheaper than building a new Honda) ;-)



James Rogerson
84-87 Civic SCCA HP
2006 S2k daily driver

#7
drag13honda

  • In the left lane
  • PipPipPip
    • Group: Members
    • Drives: 89 Acura Integra RS
When you get back, pics and price on the civic roll bar, please?