20 replies to this topic

[soycory]

If you have Civic knuckles you could just put new hubs and bearings into them rather than looking for used Integra parts and hoping the bearings are still good.
https://www.ebay.com...119.m1438.l2649

I thought the Civic knuckles had different spacing or smaller hub or something... Did I misunderstand?

[1985 CRX SI]

I thought the Civic knuckles had different spacing or smaller hub or something... Did I misunderstand?

Basically the same knuckles. The same bearings. The only difference is the hubs themselves (spline count). I am running Civic knuckles with Integra hubs in new bearing in my swapped CRX

[Site]

Basically the same knuckles. The same bearings. The only difference is the hubs themselves (spline count). I am running Civic knuckles with Integra hubs in new bearing in my swapped CRX

 

so glad youve posted this...gonna save me a couple of hundred pound in the uk if this works...got spare set of 1G CRX knuckles im gonna try this with!

[Site]

Basically the same knuckles. The same bearings. The only difference is the hubs themselves (spline count). I am running Civic knuckles with Integra hubs in new bearing in my swapped CRX

 

Sorry to bother you some more, but Im currently trying to look at my driveshaft options for my B18C6 swap in the UK. Ive seen the thread but was wondering if you knew the spline count of the integra hubs please. Only as I believe someone said I should use 3G civic 4WD Shafts as they are 22.75" but the spline count appears to be 26 for the outer CV's. I have Mk1 CRX D16ZC hubs and driveshafts which from all accounts seem to be 26 splines on the outer CV's. So im trying to save myself the hassle of buying the integra hubs and new bearings if I can use my CRX ones. I believe the 3G civic OEM ones are 23 splines.

 

Unfortunately these parts are at my mates garage and I cant go and count them myself for around a month but wanted to order parts or work out if I might have enough to put something together as it is. 

 

I will be using an SR3 hydro intermediate shaft but I might change to an SK7 if it appears to be a better choice! Im trying to get away from having to buy the £350 hasport axles as they are pricey when getting shipped to the UK.

 

I think I can use Cardone 60-4084 left hand shaft which has a 27 inner and 26 outer spline count and is 22 3/16" length with an M22x1.5 spindle which matches the 4WD shafts and is female inner to male outer so would work with the SR3 shaft and is from the following cars Acura Integra 1998-94; Honda Civic 2000-99, Civic del Sol 1994.

 

If not I could use a cardone 60-4054 which is 22 13/16" 27 inner and 26 outer spline count for the left...this shaft is a male to male though and requires an SK7 intermediate but I am hoping the one before works with that side...also it would make it cheaper to replace any axles that have broken if I can get off the shelf shafts rather than the R-axle/hasport pairs that are fairly expensive.

 

I will use the 4WD Cardone 60-4055 for the right hand side which is 27 inner and 26 outer at a length of 22 3/4". This is only 0.25" longer than the Hasport shafts which were measured at 22 1/2". 

 

What Im trying to confirm is are the mk1 CRX D16ZC outer splines 26 like the shafts mentioned above, or is it just the integra hubs as when i look for replacement CRX shafts for my ZC cardone seem to suggest that the 4WD shafts fit the CRX Si / HF which i thought was the model with the ZC...if so then it means that ZC Shafts or MK1 CRX Si D16ZC hubs can be used which is surprising! Also when i look for a Mk1 CRX 16i 1.6L which would be the D16ZC the CV joints I can buy suggest they are a 26 spline outer which is the same as the integra's...so I may be able to just use those hubs which is interesting...issue im having is hte outer CV's for integra's suggest a seal size of 55m compared to the 49mm of the Mk1 CRX...I have no idea what the seal size is!

 

https://www.ebay.co....P 92KW (Petrol)

 

https://www.ebay.co....=item2cadf5e5cc

[Site]

For anyone interested, the UK Integra 86-89 D16 Hubs and bearings have the same part number as the Mk1 CRX D16 hubs and bearings...so I assume that instead of needing the integra knuckles/bearings/hubs for the Hasport shafts a Mk1 CRX could be used which may be easier to find in the UK...glad I didnt throw these hubs away now!

[1985 CRX SI]

 Yes mk1 CRX D16ZC outer splines 26 inner 27 splines. 

 

Rockauto

CARDONE SELECT is new not remanufactured

 

CARDONE SELECT 664054 {#44306SD9013}  $47.79 (NO CORE CHARGE) 

Front Left; 4WD; Wagon; Base Model

 

A-1 CARDONE 604055 {#44305SD9013} Reman. $48.89 $10.00 core charge

   

 Front Right; 4WD; Base Model